
ZX-T
Sensores de medición por contacto inteligentes
ZX-T resulta ideal para aplicaciones donde el objeto puede contener depósitos de aceite u otras microestructuras. En este caso, la medición por contacto constituye el método más fiable.
- Concepto de plataforma modular para distintas tecnologías de detección
- Tipos de retracción neumática para una inspección automatizada
- Medición multipunto con un máximo de 8 sensores
- Alarma de fuerza de presión para evitar un funcionamiento incorrecto
- La robusta estructura de cojinetes de bolas garantiza una larga vida útil
Especificaciones y modelos disponibles
Ordering information

Sensors
Sensor heads
Note: The resolution refers to the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected.
Amplifier units
Accessories (order separately)
Calculating unit
ZX-series communications interface unit
SmartMonitor sensor setup tool for Personal Computer connection
, | |
Cables with connectors on both ends (for extension)
*
undefined
* Robot cable models are also available. The model numbers are ZX-XC_R.
Preamplifier mounting brackets
Actuators
Measuring ordinary flat surfaces (standard |
![]() |
||||
![]() |
|||||
![]() |
|||||
![]() |
|||||
![]() |
|||||
Mounting D5SN-TN1/-TF1 or commercially |
![]() |
Note:
Replacement possible
Conversion adapter required
Specifications

Amplifier units
Sensor heads
9
9.
These figures are representative values that apply for the measurement mid-point, and are for when the provided actuator is used, with the actuator moving downwards. If the actuator moves horizontally or upwards, the operating force will be reduced. Also, if an actuator other than the standard one is used, the operating force will vary with the weight of the actuator itself.
|
||||
Operating: 0 to 50°C, storage: - 15 to 60°C (with no icing or condensation) |
||||
Operating and storage: 35% to 85% (with no icing or condensation) |
||||
Instruction manual, preamplifier mounting brackets (ZX-XBT1) |
1.
When using the ZX-TDA11/41 with the SmartMonitor, either the ZX-SFW11EV3 or the
ZX-SW11EV3 SmartMonitor must be used. Earlier versions cannot be used.
3.
The response speed of the linear output is calculated as the measurement period x (average count setting + 1).
The response speed of the judgement outputs is calculated as the measurement period x (average count setting + 1).
4. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.
7. The resolution is given as the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected. This value is taken 15 minutes after turning ON the power with the average number of operations set to 256.
9. These figures are representative values that apply for the measurement mid-point, and are for when the provided actuator is used, with the actuator moving downwards. If the actuator moves horizontally or upwards, the operating force will be reduced. Also, if an actuator other than the standard one is used, the operating force will vary with the weight of the actuator itself.
1.
When using the ZX-TDA11/41 with the SmartMonitor, either the ZX-SFW11EV3 or the
ZX-SW11EV3 SmartMonitor must be used. Earlier versions cannot be used.
3.
The response speed of the linear output is calculated as the measurement period x (average count setting + 1).
The response speed of the judgement outputs is calculated as the measurement period x (average count setting + 1).
4. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.
7. The resolution is given as the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected. This value is taken 15 minutes after turning ON the power with the average number of operations set to 256.
9. These figures are representative values that apply for the measurement mid-point, and are for when the provided actuator is used, with the actuator moving downwards. If the actuator moves horizontally or upwards, the operating force will be reduced. Also, if an actuator other than the standard one is used, the operating force will vary with the weight of the actuator itself.
¿En qué podemos ayudarle?
Si tiene alguna duda o necesita información sobre un presupuesto, póngase en contacto con nosotros o envíe una solicitud.
Contacten conmigo ZX-T

Gracias por enviarnos su solicitud. Le responderemos lo antes posible.
Tenemos dificultades técnicas. Su formulario no ha sido enviado. Porfavor, acepte nuestras disculpas e inténtelo de nuevo más tarde.\ Detalle: [details]
DownloadPresupuesto para ZX-T
A través de este formulario puede solicitar cotización del producto escogido. Por favor, cumplimente todos los campos marcados con *. Sus datos personales serán tratados con la máxima confidencialidad.

Gracias por la cotización solicitada. Le enviaremos la información solicitada lo antes posible.
Tenemos dificultades técnicas. Su formulario no ha sido enviado. Porfavor, acepte nuestras disculpas e inténtelo de nuevo más tarde.\ Detalle: [details]
Download